TCP/IP host configuration utility
dhcp.client [-abdmnRru] [-A num] [-D ident] [-h hostname] [-I num] [-i interface] [-P port] [-p port] [-s host] [-T secs] [-t num] &
- -A num
- The dhcp.client declines addresses if they fail an ARP probe (see RFC 2131 and RFC 5227). This option sets the number of consecutive ARP probe tests of the assigned address that can fail before dhcp.client gives up. The default is 5; a value of 0 turns off ARP probing.
- Apply the assigned IP address as an alias instead of overwriting the current configuration.
- Request the DHCP server to send its response packets only to the client where appropriate (default is to request the server to broadcast).
- -D ident
- Specify the client identifier. The default identifier is the MAC address.
- -h hostname
- Hostname of client (default is supplied by the server if the hostname is available).
- -I num
- The number of times to poll waiting for interface to be available
Polling is done every 2 seconds.
You can use this option to make dhcp.client wait until the interface it's to use is available. This is useful in a boot environment when you might not know when the driver is running and registered with the TCPIP stack. The exit status is 2 if no interface is found.
- -i interface
- The name of the interface to configure (e.g. en0, en1). The default is the first interface found.
- (BlackBerry PlayBook OS extension)
Instead of writing the domain and nameserver data to /etc/resolv.conf (the default),
write the data to the _CS_DOMAIN and _CS_RESOLVE
memory configuration-defined values (see
in the Neutrino C Library Reference):
- Domain name.
If you specify -m and -n together, the domain is added, but the nameservers aren't.
- Don't add the DHCP-supplied nameservers to /etc/resolv.conf or _CS_RESOLVE. If you also specify -m, the domain is added, but the nameservers aren't. If you don't specify -m, neither the domain nor the nameservers are added.
- -P port
- DHCP server port (default is dhcp port or port 67).
- -p port
- DHCP client port (default is dhcpc port or port 68).
- Don't apply the DHCP-supplied default route. If you specify this option, the default route supplied by the DHCP server isn't applied, but it's still supplied to the dhcp-up script (see below) in case you wish to apply it later.
- Add .node_number to the resolv.conf file name.
Off by default.
QNX Neutrino ignores the -r option.
- -s host
- Accept packets from this server only; ignore responses from other servers.
- -T sec
- Specify the time, in seconds, to wait for the client to complete (server ACK) its negotiation with the server. This is applied every time the client returns to the initialize (DISCOVER) state. If a timeout occurs, dhcp.client terminates with an exit status of 3.
- -t num
- Attempt to reach the server num times before giving up
and terminating (the default is forever).
Each attempt lasts 1 minute.
You're likely to use this option in combination with the -u option so that dhcp.client times out after a specified number of attempts.
- Don't move dhcp.client to the background until the interface is
This option is useful for spawning dhcp.client. The process doesn't move to the background until it has contacted a server and applied a TCP/IP configuration. The exit status is 3 if no server responds.
The dhcp.client obtains the TCP/IP configuration parameters dynamically from a DHCP (Dynamic Host Configuration Protocol) server, then automatically configures your TCP/IP host. You don't have to provide an IP address or any configuration parameters, or run any configuration utilities.
If dhcp.client is terminated, it releases the DHCP address assigned by the server back to the server. If the client is terminated with SIGPWR, the address isn't released; the lease will timeout or be continued at client restart (depending on server policies).
The minimum commands to run under QNX Neutrino are:
io-pkt-v4 -dne2000 -ptcpip if_up -p enx dhcp.client & if_up enx
io-pkt-v4 -dne2000 -ptcpip dhcp.client -Ix -u
If you wish dhcp.client to apply the IP address as an alias instead of overwriting the currently assigned IP address, you must pass the -a option. This option is useful if you wish to assign multiple IP addresses to an interface.
By default, dhcp.client searches for an unconfigured interface to provide service. If AutoIP is in use, an unconfigured interface will not be available, and the dhcp.client will terminate. In order for dhcp.client to provide service to an interface that already has an IP address assigned to it, use the -i option (in combination with -a), and the interface will have both a DHCP and AutoIP IP address assigned to it.
This utility obtains and implements the following information from the DHCP server:
- Broadcast address
- Gateway (default route)
- IP address
If this file exists, it is run after a DHCP server has been contacted and the configuration options above have been applied. This file can be a binary program or a script and must be executable (see chmod ). If the file is a script, the first line must be the command interpreter. For example:
Environment variables, which contain the configuration that was obtained from the server, are passed to this file. When the file is spawned, it doesn't inherit the full environment. For example, the PATH environment variable isn't available. To determine which variables are available, you can create a dhcp-up script like this:
#!/bin/sh env > /tmp/config
The environment definitions are:
- The interface that was configured (e.g. INTERFACE=en0).
- The client IP address that was obtained from the server (e.g. IPADDRESS=10.0.0.1).
- The client netmask that was obtained from the server (e.g. NETMASK=255.0.0.0).
- The hostname of the client (e.g. HOSTNAME=node1).
- The client broadcast address that was obtained from the server (e.g. BROADCAST=10.255.255.255).
- The gateway that the client is to use (e.g. GATEWAY=10.0.0.2).
- The DHCP server's ID (IP address) (e.g. SERVER=10.0.0.3).
- NAMESERVER1, NAMESERVER2
- The nameserver that the client is to use (e.g. NAMESERVER1=10.0.0.4).
- The time at which the lease was obtained (e.g. LEASEOBTAINED=Mon Oct 30 16:46:10 2000).
- The time at which the lease expires (e.g. LEASEEXPIRES=Mon Oct 31 16:46:10 2000).
- A DHCP relay agent forwards packets between dhcp.client and the DHCP server if they're on different networks. This is the IP address of the relay agent if it's present.
- The hostname of the DHCP server.
- The domain supplied by the DHCP server to be added to /etc/resolv.conf or CS_DOMAIN (configuration string).
- The next server to use in bootstrap. If a FILENAME was supplied, it would be obtained from this server.
The following options are available but not applied by the dhcp.client process:
- The filename supplied in the server response (e.g. FILENAME=/bootimg).
Any other options are defined as environment variables OPTION x, where x is the option number. If the option is known, dhcp.client tries to format it as readable information. If the option isn't known, dhcp.client displays each octet as hexadecimal (e.g. OPTION200= F1 AA 56 42).
Currently, dhcp.client is aware of options 1 to 61.
This file defines the DHCP options that the client wishes to obtain from the DHCP server. You need this file only if you're adding custom DHCP option handling to the /etc/dhcp/dhcp-up file. If you add code to the dhcp-up script to handle an option, you must also add this option to /etc/dhcp/dhcp-options. The options listed in dhcp-options file are sent to the server in addition to the options:
- 1 — subnet mask
- 6 — domain name servers
- 12 — hostname
- 15 — domain name
- 3 — gateway
- 28 — broadcast address
which the dhcp.client process itself includes.
Here's an example of the dhcp-options file:
200 150 #This is a comment 90
Specify each option on its own line, listing them in order of priority. Comments must be on a separate line; they can be up to 80 characters long.
The dhcp.client utility requires the libsocket.so shared library.
- An error occurred.
- No interface was found.
- No server responded.
Errors that occur during configuration are reported to the system log.